White rectangular tile already lined the bathtub encompass in Brittney Good’s lavatory, reaching from the bath to the ceiling. The remaining partitions had been painted drywall, leaving a big part beside the tile with out the identical floor element.
As an alternative of extending tile throughout the room, Good saved the drywall and hooked up slender wooden strips over it. Many of the vertical battens are only one/4 inch deep and 1-3/8 inches extensive, whereas a horizontal 1×4 runs beneath the ceiling. The present wall turns into the house between the strips somewhat than being lined with new panels.
Paint, spackle, and caulk ultimately conceal the joints and fasteners. What stays seen is the grid fashioned by the wooden, with the unique drywall sitting between every raised batten.
Plain drywall remained beside the tiled tub encompass
Shiny white tile covers the total top of the bathtub encompass, whereas painted drywall begins at its periphery and continues throughout the remainder of the toilet. The wall itself was saved as a result of it could type a part of the completed board-and-batten remedy.
Earlier than any wooden was put in, the drywall was cleaned, primed, and painted. Portray at this stage avoids having to coat the slender areas between battens after they’re hooked up.
Horizontal board establishes the highest of the remedy
A 1/2-inch-thick 1×4 kinds the horizontal board slightly below the ceiling. Its size is taken from the wall itself earlier than the measurement is transferred to the wooden.
The undertaking makes use of a V-shaped pencil mark for cuts, with the purpose of the V positioned on the measurement. That leaves one precise intersection for the noticed as an alternative of counting on both fringe of a large pencil line.
Ceiling helps place the lengthy higher board
The lower board is dry-fitted throughout the wall earlier than it’s nailed in place. A stage can be utilized to examine its place, whereas this set up additionally makes use of the ceiling as a reference as a result of the board runs simply beneath it.
Stud areas are marked earlier than fastening, permitting the lengthy horizontal piece to be secured into framing the place doable somewhat than counting on drywall alone.
Batten beside the tile is thicker than the others
The tile initiatives from the drywall far sufficient that the usual 1/4-inch battens would depart an uncovered edge on the transition. A 1/2-inch-thick alder strip is used beside the bathtub encompass as an alternative.
Its thickness modifications, however its 1-3/8-inch face width matches the opposite battens. The broader depth meets the projecting tile whereas preserving the identical strip width throughout the wall.
Ten-inch areas set the batten sample
Completely different gaps had been examined earlier than a 10-inch house was chosen between battens. Marks are made at each the underside and prime so every strip will be positioned on the identical interval as an alternative of counting on a single measurement.
The vertical size is then measured at every marked place. Taking that measurement on the set up level accounts for small variations between the baseboard and higher board throughout the wall.
Quarter-inch battens work with the present baseboard
Many of the vertical strips are 1/4 inch deep and 1-3/8 inches extensive. The present baseboards are about 1/4 inch deep on the prime, which influenced the selection of fabric.
Matching these depths permits every batten to satisfy the highest of the baseboard with out projecting previous it. The baseboards can keep in place as an alternative of being eliminated and changed to accommodate thicker wooden.
Scrap wooden retains the spacing from drifting
After the primary two battens are positioned, a scrap piece is lower to the precise distance between them. That piece turns into a spacer for the remainder of the set up somewhat than measuring 10 inches once more at a number of factors on each strip.
The spacer is moved upward between adjoining battens earlier than the middle nails are pushed. If a skinny strip bows to both aspect, it may be pushed towards the template and mounted on the right distance.
Battens are mounted on the prime, backside, and middle
Every vertical strip is first secured at its decrease and higher ends, then mounted via the middle. In contrast to the horizontal board, the battens don’t must line up with wall studs; the undertaking makes use of 1-1/4-inch brad nails lengthy sufficient to lock via the drywall.
The method repeats throughout the wall till the painted drywall is split into slender vertical sections. No sheet materials is put in between these strips.
Similar remedy continues onto the opposite partitions
The battens proceed past the primary wall and into the areas round the bathroom, vainness, switches, and different mounted components. The place a batten meets a change plate, the wooden is split into separate higher and decrease items somewhat than transferring the established spacing to keep away from the impediment.
The ends may also be lower to satisfy the projecting change plate as an alternative of leaving a sq. wooden edge behind it.
Brad nail holes are crammed earlier than portray
Set up leaves small brad nail holes alongside each batten. Fast-drying spackle is pressed into every opening with a finger, and extra materials is wiped away earlier than it units.
The undertaking makes use of a no-sanding-required filler, so preserving every restore flush with the wooden at this stage avoids including one other sanding cross throughout the slender strips.
Caulk closes the joints across the wooden
A skinny bead of caulk goes anyplace the boards or battens meet one other floor, together with drywall, ceiling, baseboard, countertop, and adjoining trim. The bead is smoothed with a humid finger to fill the joint with out spreading caulk throughout the faces of the wooden.
These crammed seams take away the slender gaps left between the added strips and the present wall earlier than the ultimate coat of paint goes on.
Paint makes drywall and wooden learn as one remedy
After the spackle and caulk dry, the battens obtain the identical white end as the encircling wall. A brush covers seams and inside edges, adopted by a foam curler throughout the flat wooden surfaces to scale back brush marks.
Matching the paint conceals the boundary between the unique drywall and the added wooden. Solely the shallow projection of every batten stays seen.
Skinny strips give the plain partitions a paneled end
The completed lavatory retains the tile confined to the bathtub encompass whereas board and batten covers the remaining wall areas. Every white part between the battens remains to be the painted drywall that was there earlier than set up.
The 1/4-inch strips present the raised edges, the present baseboards terminate them on the ground, and the 1×4 connects them beneath the ceiling. The consequence modifications the plain partitions with out including tile or overlaying them with full wooden panels.
Would you retain the tile across the tub or carry it throughout the remainder of the toilet?
